Using a pool brush on an extendable pole, walk around the pool and brush the sides downwards to remove any algae or dirt that may be clinging to the sides.
In hot sunny weather it can climb remarkably quickly with these fitted. If the pool is being used often when you have family staying for instance then I would check the water condition using a test strip or test liquid, and add any chemicals that may be necessary. Otherwise I normally do his once a week after cleaning. Fortunately, the only real work you need to do in order to keep your pool in good order, is once per week. It generally takes me just 45 minutes from start to finish most weeks unless the pool is particularly dirty after a storm has blown debris into the pool.
If you can, then you should do this either before anyone goes in for a swim or at least an hour after the last swim. This is mainly because the swimmers will disturb any dirt in the pool which will now be floating in suspension in the pool water. That dirt should be allowed to settle on the bottom so you can vacuum it up, so allow an hour or so if possible. If the pool is very dirty, so you will need to vacuum to waste , rather than on the filter setting, then top the pool up above the normal level as water will be lost during the waste vacuuming process.
If you have lots of leaves on the bottom of your pool then use a pool rake or pool net to remove as many as possible. When you use the leaf rake, try to do this as gently as possible to avoid disturbing any fine dirt from the bottom. If you do then it is best to leave it to settle again before vacuuming.
Gently bush the sides of the pool with the pool brush to remove any dirt or algae as well as doing the same for the steps or ladder and anywhere else in your pool where dirt accumulates that is difficult to remove with the vacuum. Empty any debris from the skimmer baskets before you start and leave the basket of out the skimmer you use to connect the vacuum hose if you do not use a skimmer plate or have a dedicated side vacuum port.
Connect your pool vacuum head to the pool pole and vacuum hose and then, after removing the air from the pool hose , connect it to the skimmer or dedicated vacuuming port if you have one. If your skimmer has two holes then use the outer most. Vacuum the entire bottom of the pool, with the multiport valve set to filter, taking your time so as not to disturb the dirt as you go. I find it quite therapeutic actually. If the pool is very dirty, so you are vacuuming on the waste setting , then keep an eye on the water level.
If it reaches the bottom of the skimmer opening then you need to stop vacuuming and top the pool up again before continuing. When you have finished remove the vacuum from the pool and replace any skimmer baskets still out. Check to see if the filter needs backwashing and rinsing. When you vacuum dirt gets trapped by the filter and after a while it becomes clogged so back pressure builds up and the suction reduces.
If you noticed the suction reducing while you were vacuuming, or the filter pressure gauge is now higher than normal, then you may need to do this. To find out how to do this then read my guide to backwashing. Visually check the pool pump strainer basket, through the see-through lid, to see if there are any leaves and other debris in there. If there are more than just a few then set the filter to closed and shut off any valves into the pump and then remove the basket and empty it.
Now is the time to check the pool water chemistry to establish the chlorine levels, the pH, the alkalinity etc and add whatever chemicals may be necessary to bring the readings to the correct level. Occasionally you may wish to take a sample of the pool water to your local pool store and get a full water analysis carried out.
You are now pretty much finished. Unless you have just shocked the pool, then I suggest you go for a swim, and if you do, that is a great time to clean along the waterline to remove any marks or other stuff there. I always do this as it is so much easier than breaking my back bending over the edge to do it. It is good practice to shock your pool every other week or perhaps even weekly if it is getting used a great deal. This will eliminate any contaminates and ensure clarity of the pool water.
Ideally you should leave the pump running after shocking the pool so it is best to shock in the evening if you can. Do not let anyone swim after shocking until the chlorine levels have dropped to a safe level. If you have an automatic pool top up system you would be unaware if the pool has sprung a leak. Make sure it does not get too high because adjusting it can become quite hard.
Meanwhile, too low total alkalinity will make the pH level difficult to control. You can use acid, which will lower the total alkalinity. If it needs increasing, you can use sodium bicarbonate. The optimal alkalinity level is around 80 to PPM. You can add Chemicals for sanitization, pH, and alkalinity. Other chemicals can help prevent staining.
The easiest way to clean pool deck areas on your own is to run a blower. Some owners though are not keen on using leaf blowers. As alternatives, you can use buckets of pool water or a garden hose.
Leaf litter can become a problem for some pool owners as well. You can begin trimming the plants in the pool area or replace overgrown ones with smaller varieties. Most of the time, calcium, as well as Cyanuric Acid, tend to stay stable every month.
However, you need to test it so you can make adjustments whenever necessary. Keep calcium hardness around to PPM. If you have a saltwater pool, you should also test the salt levels. You can do it yourself or take a sample of the water and to a pool expert to have it analyzed. Have it tested for metals, total dissolved solids, Cyanuric Acid, and others. This way, you can adjust the levels accordingly.
Busy pools require cleaning more frequently. However, you typically only need to clean the diving board and slides once to twice a year. Use the right cleanser and make sure you do not get the chemical into the pool. Ensure the diving board bolts or the ladder tread bolts on the slides are not loose. Cartridge filters should have their elements replaced at least every months. Annual tuning up of pool cleaners and lubricating the O-rings can also keep the pool running smoothly.
Pool Troopers offers all these tune-ups and yearly maintenance tasks as part of our spring special and we can do it year-round on your startup anniversary for you if you sign up. Aim to follow this pool maintenance checklist to make sure your pool stays clean, safe, and function all year round. Contact Pool Troopers for any additional tips on maintaining your swimming pool, today! CPC - Tex Lic. AZ ROC For questions about your account call For questions about starting service please give us a call or schedule online today.
Selling Your Company? Find Your Location Learn More. No Comments 0 0 0. The Checklist This list is designed to serve as your guide in caring for your pool. That said, here are our recommendations on how you can keep your pool in its best condition: Daily Maintenance 1. Check the level of water. Another option is to start a siphon hose, which is a common way of draining the pool. Check the filter and pump. Inspect the pool cleaner. Check the baskets. Make sure the water circulates properly.
Weekly Maintenance 1. Check the chemical levels. Check alkalinity. Add chemicals. Clean the pool deck. Monthly Maintenance 1. Check calcium and CYA levels. Test Salt Levels. Yearly Maintenance 1. Clean slide surfaces. Tighten bolts. Disassemble and thoroughly clean the filter, replace cartridge elements. Most Popular.
0コメント